Sound dampening forum discount!
Mod/Admin please sticky.
If you have been following Cherry's thread we were looking into Sound Dampening. Well it panned out, but not a group buy per say. We are getting 20% off Sound dampening products via Elemental Designs: www.edesignaudio.com Simply head to their site. Buy only what you want/need. At checkout enter the code edeadba and you will get 20% off the PRODUCT. Note shipping is standard and extra. EDIT: Since so many people are asking and to lazy to measure for themselves Ive done the work for you. Below SQ Feet assessments are APPROXIMATES only with some extras added. If you add it all up and buy it all you may wind up with leftover- which is better than not enough! All values are single layers and have some extra added in. Trunk Lid: 9 sq/ft Sides of trunk (both): 14 sq/ft Bottom of trunk: 15 sq/ft Trunk total: 38 sq/ft Back seat under bench seat: 10 sq/ft Back seat sides (coupe- 2dr) 13 sq/ft Door: Skin (very outer most part- both): 16 sq/ft Inner door (under neath door panel): 9 sq/ft Total for 2 door coupe: 86 sq/ft I advise you to consider the liquid stuff for your trunk lid. It can get between the sheet metal and the sheet metal skeleton where mat cant get. But you have to remove the trunk lid! Also I advise the use of a better mat for the door skin, under the rear seat (especially here!!!!) and the rear sides for 2 doors. |
we need a group purchase forum section like J-Body has.
|
This isnt a group purchase.
Im not sure if theres a time limit on that code either. So dont wait around people! |
i will be ordering 100 ft of 45 mill in a day or 2
|
how much will one gallon cover??
|
simply because you've seen alot of this stuff... have a recommendation/suggestion for what version of that stuff to use?
and you might want to post your other link that details this stuff, over here... for comparison reasons. |
edead120???
how much would we need for the trunk??? |
Quote:
http://www.edesignaudio.com/elementa...edeadwhere.php |
Quote:
That link only covers the older mats, so its not 100% anymore. So its useless to post it here. Its all a money pit really. The more you spend the less you will hear. If its not to bad get the $1 stuff, want better get the $2 stuff. want the best, get the $3.50 stuff. Personally Im getting some of both. Im going to do the trunk with eDed45. Im doign the back seat and cabin with eDead80. A quart of the liquid stuff for the trunk lid. This will get into the sheet metal frame to sheet metal areas the mat wont! I will try and work on some numbers for you guys tonight or tomorrow. |
i'm thinking i'm getting a gallon of the liquid for the outer skin (at least) maybe i'll do the some of the trunk in that too. and regular 80 mat for the door/backseat. is the neoprene worth investing in?
i won't have time to do this till summer vaca though. so i'll be looking forward to your feedback about it. i think the liquid will be much easier to use on the inside of the door (on the plastic) |
Its not easy to put on vertical surfaces.
Im going to remove my trunk lid to do it. |
looks pretty thick... i don't imagine it dripping alot if your doing thing coats.
|
Has anyone checked the shipping prices yet? You have to create an account in order to view them.
|
Just how much do you have to take your car apart to do this?
|
Quote:
Where do you want it? |
Updated first post with estimates.
Some one with a 4 door can measure up the rear doors and figure the rear sides (under the back seat upright where that strange carpeted plastic bumps are). |
thanks for the addition. (coupon AND estimates)
:thumb: |
I put in 90 Sq ft eDead45, 1 qt liquid. Shipping from Idaho to Ohio is only $20- so its reasonable...
Also note that its only a discount on MAT, not the liquid stuff! I wont be able to buy until next week... :( |
not liquid...hmm.... that changes things (not much though)
i know the inner/outer skins need dampening, but do the inside of the doors? and like i said before... does the neoprene closed cell foam make a big difference/where does it get mounted? |
Well what are you looking for?
I wouldnt pay the price for that stupid foam crap. Just get some jute from a flooring store, Lowes, Home Depot, etc. The mat will reduce the structure noises and help with road noise. The jute will help alot with road noise. Especially under the rear seat. Its a horrible area there. |
i'm looking to quiet things down alot and improve sound quality.... i'm not sure how else to phrase that(its a pretty general response). :lol:
|
The only noise I get is from the damn air I hear on the drive side rear. Other then that if I can get that trunk under control from rattling then I will be good.
|
Quote:
Probably in the firewall, roof for wind noise, inner wheel well, vehicle floor seem like good spots. I would like to reduce external noise, I don't have a heavy hitting sound system that vibrates my nuts when I drive or anything like that. |
i think the liquid takes a while to fully cure ( a month ), thats why I am not gettin it. it will take about 100 ft to do the whole impala ( including the floor xcept the roof). I think a gall of liquid dose 60 sq ft (depends on thickness applyed)
the impala trunk lid is 4 ft x 2.5 ft, doors are 7 ft x 2 ft , trunk sides are 2 x4, whole floor area is 11 x 4, I am getting 100 ft of 45 mill, I will do everything but the floor, see how it sounds then decide to do floor or second layer on doors and trunk. that should gove everyone a good idea what they need, impala is a little bigger then the alero. |
Just bought 50ft of E80 thanks for the code
|
just order 50 sq ft Thank you ryan & Cherry!!
|
110 sq ft ordered.
I allowed some extra so I can double layer under the back seat. Also in my estimate I did NOT include the package tray (where 6x9's go). Total shipped was under $110. I will buy the roller locally for like $6 vs there $12.50 :p |
^^ they sent me one with the 50 sq ft i ordered
|
Just got my 50sq ft of E80 going to put it in tomorrow :)
|
Must be nice.
Fed ex is the absolute ghey. I hate fedex. They have to be the worst shipping company ever. I dont understand why business's use them for residential shipments. I got an email update on shipping. Fedex didnt deliver yesterday as "nobody was home". Which is a bold faced lie. The Fedex driver never went to the door. I called last night. The customer rep said theres no reason my package shouldnt of just been dropped off... No sig required... So she said she would send a note to the driver to just leave the package in my hallway. Today I got another email update with the same excuse. Im not going to go to their terminal 45 minutes away to pick up my delivery. I will simply charge back on my credit card. This stuff infuriates me instantly with Fedex. ive had this same very issue with them 10 years ago, and exactly why its been 10 years since Ive dealt with Fedex. I will make it an issue to give the customer service that bit of info... |
Evidently the Fed Ex driver couldnt find my place? At any rate got my package today.
I didnt get a free roller though... :( Oh well. My measurements were 33-38 mills. Man this is much thinner than I anticipated. Guess I should of broke out the calipers before buying. |
whats a good thickness for the job?
|
In hind sight I wish i would of went for the eDead 80. Its about double the thickness. this .040" stuff makes me wonder...
|
so you should use 80 for the doors?
just trying to figure out what i need before i buy. |
No, I wish I would of bought 80 for all of it.
The low end stuff is thin... Im debating keeping it or selling it off to go bigger. need some more time to consider and collect my thoughts on this one. |
alright. so i'll go 80, when i get mine.
i don't want to have to redo it again and again. |
Well Im going to just put this stuff on.
Even if I have to double it up in some areas it comes in at the same price as the next level up anyhow. Rollers... I went today to a locally grown big box store (only about 6 stores in total). They have an audios ection with Dynamat rollers. $12. My dad said lets look int he wall paper section. Same roller, different color handle- $5. |
purchased. only the 45 but for my budget and the fact that i wasn't gonna put anything in at all... that'll suffice.
|
:yahoo: that its still working...
|
cool imma get me sum more
|
All times are GMT -4. The time now is 06:24 AM. |
Powered by vBulletin Version 3.6.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.