will a 3800 eaton M90 bolt onto a 3400?

Ian 2000GL LA1 · 10-22-2009, 01:10 PM

i know its probably been asked but i can get one cheap and wondered if this would work.

lvemy3100 · 10-22-2009, 01:19 PM

so you think it may have been asked then dont search at all and ask the question once again...

not trying to be mean just think that there was no need for you to make this thread..

the answer plain and simple is ... NO

Ian 2000GL LA1 · 10-22-2009, 01:24 PM

Quote:

Originally Posted by lvemy3100

so you think it may have been asked then dont search at all and ask the question once again...

not trying to be mean just think that there was no need for you to make this thread..

the answer plain and simple is ... NO

problem is i did do some searching but all i found were a bunch of resposes like urs.

Redog · 10-22-2009, 01:24 PM

I looked into it myself

It could work, but you'll have to have a lot of piping and such for it. A s/c on a 3400 motor sits over the front valve cover

Ian 2000GL LA1 · 10-22-2009, 01:25 PM

what is needed to fit it to the 3400?

Ian 2000GL LA1 · 10-22-2009, 01:26 PM

Quote:

Originally Posted by Redog

I looked into it myself

It could work, but you'll have to have a lot of piping and such for it. A s/c on a 3400 motor sits over the front valve cover

slightly confuesed? so it will bolt on but it has some goofy overhang?

lvemy3100 · 10-22-2009, 01:32 PM

Quote:

Originally Posted by Ian 2000GL LA1

problem is i did do some searching but all i found were a bunch of resposes like urs.

so you found tons of people telling others that it wont work but still felt the need to ask again??

an m90 will require a completely new lower intake manifold to be fabricated... so unless you have 10's of thousands of dollars to make a new LIM it wont work at all

just go turbo or buy one of the Magnuson kits floating around or buy a vortech kit from PFYC.com

Ian 2000GL LA1 · 10-22-2009, 01:35 PM

Quote:

Originally Posted by lvemy3100

so you found tons of people telling others that it wont work but still felt the need to ask again??

an m90 will require a completely new lower intake manifold to be fabricated... so unless you have 10's of thousands of dollars to make a new LIM it wont work at all

just go turbo or buy one of the Magnuson kits floating around or buy a vortech kit from PFYC.com

what crawled up ur ass and died? GTFO if your going to act like ur on the rag.
all i want is some streight forward answers not someone being miserable.

TheEdgeofSanity · 10-22-2009, 01:43 PM

straight forward answer: NO it won't work.

natedawg9640 · 10-22-2009, 01:50 PM

I heart this thread

Nate's Alero · 10-22-2009, 01:52 PM

Quote:

Originally Posted by TheEdgeofSanity

straight forward answer: NO it won't work.

too bad, least it would make the 3400 SOMEWHAT desirable

lvemy3100 · 10-22-2009, 04:35 PM

Quote:

Originally Posted by Ian 2000GL LA1

what crawled up ur ass and died? GTFO if your going to act like ur on the rag.
all i want is some streight forward answers not someone being miserable.

um you were the one who said that my straight forward answer wasnt good enough.. you even went so far as to say that you got the same answer by seaching the forums but even that wasnt good enough for you..

I was being nice and was not being miserable.. If I wanted to be a d!ck about I could have said "WTF you seriously couldnt check the million other threads and figure out the same thing everyone else has?? NO IT WONT WORK JACKASS DONT BE SO STUPID"

now obviously that isnt what I said so please STFU.. lol

Redog · 10-22-2009, 04:46 PM

The manifold WILL NOT SIT between or replace the current manifold