Aleromod.com Aleromod.com
Old 10-01-2016, 06:15 AM   #1
mutley666
GX Member
 
Join Date: Aug 2015
Location: Marbella, Spain
Posts: 4
mutley666 is on a distinguished road
Timing Chain

Hello all. Finally getting round to fitting new timing chain on my 2.4 ld9
Couple of questions,
I got new cam and crankshaft sprockets in the kit, should I fit these also?
If so I cant find the torque settings for the crank pulley or the cam sprocket bolts.
Any ideas folks?
Thanks.
P.S
I notice I need a tool to hold the cam sprockets and crankshaft pulley when tightening.
Is there a way round this? Dont want to buy the tools to do 1 job!!

Last edited by mutley666 : 10-01-2016 at 09:31 AM.
mutley666 is offline   Reply With Quote
Old 10-01-2016, 09:46 AM   #2
Garion1076
GX Member
 
Garion1076's Avatar
 
Join Date: Feb 2010
Location: Charlotte, NC
Posts: 26
Garion1076 is on a distinguished road
Quote:
Originally Posted by mutley666 View Post
I cant find the torque settings for the crank pulley or the cam sprocket bolts.
I bookmarked this webpage years ago - very helpful info about the 2.4 LD9 engine: http://quad4forums.com/forums/techdata.php
There is a Fastener Tightening Specifications section that is pretty extensive - hopefully what you need is there...if not, someone else on this forum might know and answer.
__________________

2001 GL4, Midnight Blue Metallic, Neutral Leather Interior
Flux capacitor & plutonium spark plugs
Garion1076 is offline   Reply With Quote
Old 10-02-2016, 09:47 PM   #3
rocketfast321
GL Member
 
rocketfast321's Avatar
 
Join Date: Jul 2011
Location: Montgomery,Al
Posts: 308
rocketfast321 is on a distinguished road
I would do gears you that far into it. The gears done wore to the chain. My water pump is leaking, and I will have the shop replace everything.
__________________
Quote:
Originally Posted by xXManwhoreXx View Post
I could never actually get rid of the alero as much as I hate it some times
Baby Sandy: 2001 2.4 Grand Am se 1.5 (auto) 32k-119k : Sept.2002-Aug.2010
Mickey: 2001 Alero GL 2.4 5-speed (Nov. 2010) 109k-???
rocketfast321 is offline   Reply With Quote
Old 10-03-2016, 12:28 PM   #4
Bahlzeron
GX Member
 
Bahlzeron's Avatar
 
Join Date: Jan 2016
Location: Grand Rapids, Michigan
Posts: 97
Bahlzeron is on a distinguished road
Did mine around the beginning of the year. Yes, put the gears and chain in as a set. There should be a piece of paper with a warning on it with the tensioner.. don't loose it. The tensioner comes with the plunger compressed, after the chain chain is installed and timed, you need to release the plunger on the tensioner.
__________________
2001 Black GX Coupe 2.4l 5 spd, short shifter, trunk lid w/ spoiler (amazingly from same original dealership), hood struts, Cosmo Evolution SRI, front & rear stb's, GAGT mirrors, more to come
1998 Bravada
I love beer, lots of beers.. I have found dark beers to be my favored.. however Labatt Blue is my go-to.
Bahlzeron is offline   Reply With Quote
Old 10-05-2016, 03:23 AM   #5
mutley666
GX Member
 
Join Date: Aug 2015
Location: Marbella, Spain
Posts: 4
mutley666 is on a distinguished road
Yep I think I will change everything.
seems silly not to.
My only question is do I need the special tools to hold the cam sprockets and crank pulley when tightening?
The cam sprockets I can probably do with the dowels in place but the crank is quite a lot of torque then another 90 degrees.
Has anyone done this without special tools?
Thanks.
mutley666 is offline   Reply With Quote
Old 10-22-2016, 12:44 PM   #6
paul ron
GX Member
 
Join Date: Oct 2009
Location: NYC
Posts: 62
paul ron is on a distinguished road
when should it be changed?.. aprox millage?

My 2000 is about 85,000miles now
paul ron is offline   Reply With Quote
Old 10-29-2016, 09:39 AM   #7
rocketfast321
GL Member
 
rocketfast321's Avatar
 
Join Date: Jul 2011
Location: Montgomery,Al
Posts: 308
rocketfast321 is on a distinguished road
Quote:
Originally Posted by mutley666 View Post
Yep I think I will change everything.
seems silly not to.
My only question is do I need the special tools to hold the cam sprockets and crank pulley when tightening?
The cam sprockets I can probably do with the dowels in place but the crank is quite a lot of torque then another 90 degrees.
Has anyone done this without special tools?
Thanks.

The crank one just slides off
__________________
Quote:
Originally Posted by xXManwhoreXx View Post
I could never actually get rid of the alero as much as I hate it some times
Baby Sandy: 2001 2.4 Grand Am se 1.5 (auto) 32k-119k : Sept.2002-Aug.2010
Mickey: 2001 Alero GL 2.4 5-speed (Nov. 2010) 109k-???
rocketfast321 is offline   Reply With Quote
Old 10-29-2016, 09:40 AM   #8
rocketfast321
GL Member
 
rocketfast321's Avatar
 
Join Date: Jul 2011
Location: Montgomery,Al
Posts: 308
rocketfast321 is on a distinguished road
Quote:
Originally Posted by paul ron View Post
when should it be changed?.. aprox millage?

My 2000 is about 85,000miles now

When the water pump goes out.
__________________
Quote:
Originally Posted by xXManwhoreXx View Post
I could never actually get rid of the alero as much as I hate it some times
Baby Sandy: 2001 2.4 Grand Am se 1.5 (auto) 32k-119k : Sept.2002-Aug.2010
Mickey: 2001 Alero GL 2.4 5-speed (Nov. 2010) 109k-???
rocketfast321 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 01:19 PM.


Powered by vBulletin Version 3.6.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.