Aleromod.com Aleromod.com

Go Back   Aleromod.com > Performance Related > General Performance

Reply
 
Thread Tools Search this Thread Display Modes
Old 11-20-2008, 10:57 PM   #1
Redog
Aleromod part owner
 
Redog's Avatar
 
Join Date: Nov 2003
Location: Far Northeast Philadelphia, PA
Posts: 18,199
Redog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond repute
Send a message via AIM to Redog Send a message via Yahoo to Redog
Exclamation HOW TO:: Corvette front brake upgrade for 99-05 N Body cars!!

ALL THIS INFORMATION IF FROM GRANDAMGT.COM AND WAS DONE ON A FEW GRAND AMS

GM part prices updated on November 20, 2008

1) Order these parts:
- 98-02 fbody caliper brackets (front) (P/N: 18026163) $69.68/each
- 97-04 Corvette calipers
---grey calipers: (P/N: 12530682)(P/N: 12530683)$116.22/each
---red (zo6) calipers: (P/N: 88895128)(P/N: 88895129) $112.49/each
- 98-02 fbody brake pads (front)
- 00-05 Impala rotors (front)
- 97-02 corvette anti-rattle clip
* all part numbers are GM numbers.
** the calipers are available at auto part stores for less, but are not GM original parts.



2) Start off by removing the wheel. Make sure you remember to use a jack stand not just a jack.



3) Next you remove the top caliper bolt. You use a 13mm crescent wrench for the bolt, and a 16mm crescent for the guide pin. You then flp the caliper back to remove the brake pads.



4) You then remove the brake line bolt from the back of the caliper. It uses a 13mm bolt as well. You might need to put the top bolt back into the caliper and hold it in place while you loosen the banjo bolt (brake line bolt).

5) Next you remove the lower caliper bolt using a 13mm crescent and 16mm crescent for the retainer. You can now take the entire caliper off.




6) You can now remove the guidepins and boots and slide them into the new calipers.

7) You can now remove the caliper bracket. For this you use a 16mm crescent or socket wrench. theres two bolts, one on top and one on bottom. Now the caliper bracket and rotor come off.



8) You now install the new rotor and caliper bracket. Make sure to use threadloc on the threads, and reinstall with a torque of 85 lbs.



9) Check the dust shield to amke sure it is not touching the rotor. Mine was ( i discovered after 100 miles of annoying scrapeing). If it is touching then use a flathead and move it about 1/2 inch away from the rotor.
bad:
good:

10) Now you can bolt the brake line up to the new caliper, (tightening to a torque of 40 lbs) and bolt the bottom part of the caliper on using new bolts. The bolts that come with GM corvette calipers are 15mm bolts. 13 mm bolts also come with the camaro brackets (knuckles). Tighten the caliper bolts to a torque of 25lbs (verify all torque settings in a hayes manual).



11) Now you can put the pad retainers in place, and install the brake pads. You can then flip the caliper up and bolt it in place. The caliper bolts torque down to 23 lbs.



12) Make sure to bleed each side after it is done. Once the job is done, make sure that the brake fluid reservoir is filled to its line.

13) Now reinstall the wheel, torque them to 100 lbs. and lower the car back down.
This is about how it shoudl look when its all done:



Here is a pic of this brake upgrade behind a 16 inch Grand Prix Wheel

__________________
33% ALEROMOD OWNER!!


2000 Olds Alero 3400 SFI 14.53 @ 94.93
1985 Olds Delta 88 307 SBO 17.96 @ 76.99
2007 Volvo V50 T5 6M 15.782 @ 89.12
www.facebook.com/kb0177

Last edited by Redog : 11-20-2008 at 11:28 PM.
Redog is offline   Reply With Quote
Old 11-20-2008, 11:20 PM   #2
billytheman1188
3500 DONE!
 
billytheman1188's Avatar
 
Join Date: Apr 2006
Location: Albany, NY
Posts: 5,915
billytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond reputebillytheman1188 has a reputation beyond repute
Send a message via AIM to billytheman1188 Send a message via MSN to billytheman1188
This is one of the few important mods i will be doing when my alero turns into a SUMMER ONLY car.
__________________
2002 3400 & 3500 GL "Ruby"-->R.I.P. 163k. My first car. Put 130k on her.
2000 3500 GLS "Robin"-->Intake,Headers,Exhaust,H&R springs,KYB AGX,Sway bars,Strut bars and more
billytheman1188 is offline   Reply With Quote
Old 11-20-2008, 11:22 PM   #3
Redog
Aleromod part owner
 
Redog's Avatar
 
Join Date: Nov 2003
Location: Far Northeast Philadelphia, PA
Posts: 18,199
Redog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond repute
Send a message via AIM to Redog Send a message via Yahoo to Redog
According to his price list and the cost of pads and rotors on Summit, all the parts come out to $648 plus tax and shipping of course.

Not bad way to spend $650
__________________
33% ALEROMOD OWNER!!


2000 Olds Alero 3400 SFI 14.53 @ 94.93
1985 Olds Delta 88 307 SBO 17.96 @ 76.99
2007 Volvo V50 T5 6M 15.782 @ 89.12
www.facebook.com/kb0177

Last edited by Redog : 11-20-2008 at 11:30 PM.
Redog is offline   Reply With Quote
Old 11-20-2008, 11:26 PM   #4
Redog
Aleromod part owner
 
Redog's Avatar
 
Join Date: Nov 2003
Location: Far Northeast Philadelphia, PA
Posts: 18,199
Redog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond repute
Send a message via AIM to Redog Send a message via Yahoo to Redog
Prices have gone up since this list was printed. Prices on GMpartsdirect.com are a little higher now, so I'm updating the costs of the parts for the GM part numbers given
__________________
33% ALEROMOD OWNER!!


2000 Olds Alero 3400 SFI 14.53 @ 94.93
1985 Olds Delta 88 307 SBO 17.96 @ 76.99
2007 Volvo V50 T5 6M 15.782 @ 89.12
www.facebook.com/kb0177
Redog is offline   Reply With Quote
Old 11-20-2008, 11:28 PM   #5
darksobsession
GL Member
 
darksobsession's Avatar
 
Join Date: Dec 2007
Location: Honolulu, HAWAII!
Posts: 683
darksobsession is on a distinguished road
Send a message via AIM to darksobsession
the benefits are... better stopping power?
__________________

sigs are annoying
darksobsession is offline   Reply With Quote
Old 11-20-2008, 11:31 PM   #6
Redog
Aleromod part owner
 
Redog's Avatar
 
Join Date: Nov 2003
Location: Far Northeast Philadelphia, PA
Posts: 18,199
Redog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond repute
Send a message via AIM to Redog Send a message via Yahoo to Redog
Yes, better stopping power and better looking behind aftermarket wheels.
__________________
33% ALEROMOD OWNER!!


2000 Olds Alero 3400 SFI 14.53 @ 94.93
1985 Olds Delta 88 307 SBO 17.96 @ 76.99
2007 Volvo V50 T5 6M 15.782 @ 89.12
www.facebook.com/kb0177
Redog is offline   Reply With Quote
Old 11-20-2008, 11:42 PM   #7
alerored04
GLS member
 
alerored04's Avatar
 
Join Date: Jun 2004
Location: New Prague, MN
Posts: 2,481
alerored04 is an unknown quantity at this point
After this mod my car stops so hard the seatbelts hurt my chest. I have yet to lock it up with these brakes for fear of flatspotting my tires before ABS kicks in. The look is pure sex though.
__________________
My car breaks alot.
(Notice I need someone to make me a sig?)
http://www.cardomain.com/ride/2598719/1
alerored04 is offline   Reply With Quote
Old 11-20-2008, 11:47 PM   #8
AlbinoMonkeyRat
Let's Play Army!
 
AlbinoMonkeyRat's Avatar
 
Join Date: Nov 2003
Location: Lockport, NY
Posts: 8,475
AlbinoMonkeyRat is on a distinguished road
what about the rears? Obviously the same procedure would be used for the 4-wheel-disc guys, but are the parts the same?
__________________
Quote:
Originally Posted by black View Post
holy crap, i just farted at work and the whole office stinks!!!!
RIP to my Alero @ 112000 miles. COD: thrown rod. TOD: 430pm, Dec19, 2011.
AlbinoMonkeyRat is offline   Reply With Quote
Old 11-21-2008, 12:30 AM   #9
AJules
GLS member
 
AJules's Avatar
 
Join Date: Aug 2007
Location: Hartford, CT
Posts: 917
AJules is on a distinguished road
You can get something very similar for under 300 bucks

http://www.mpracing.org/store/index....&productId=369

or you can try to get in on this group buy

http://www.gaownersclub.com/forum/sh...ad.php?t=95922
AJules is offline   Reply With Quote
Old 11-21-2008, 01:02 AM   #10
Cliff8928
Moderator
 
Cliff8928's Avatar
 
Join Date: Nov 2004
Location: Long Grove, IL
Posts: 5,002
Cliff8928 is on a distinguished road
Send a message via ICQ to Cliff8928 Send a message via AIM to Cliff8928
You could definitely do it for less than $300 if you wanted to...
__________________
Cliff Scott
2004 Alero GX w/sport pkg - Sold, living somewhere in WI now.
2011 Saab 9-5 Turbo4 M6
2004 Corvette Convertible M6
1994 Chevy Beretta - Quad4/M5
Cliff8928 is offline   Reply With Quote
Old 11-21-2008, 01:54 AM   #11
Redog
Aleromod part owner
 
Redog's Avatar
 
Join Date: Nov 2003
Location: Far Northeast Philadelphia, PA
Posts: 18,199
Redog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond reputeRedog has a reputation beyond repute
Send a message via AIM to Redog Send a message via Yahoo to Redog
Quote:
Originally Posted by alerored04 View Post
After this mod my car stops so hard the seatbelts hurt my chest. I have yet to lock it up with these brakes for fear of flatspotting my tires before ABS kicks in. The look is pure sex though.

How big are your wheels? And is the offset different with these brakes? That's the only thing that's on my mind about the upgrade
__________________
33% ALEROMOD OWNER!!


2000 Olds Alero 3400 SFI 14.53 @ 94.93
1985 Olds Delta 88 307 SBO 17.96 @ 76.99
2007 Volvo V50 T5 6M 15.782 @ 89.12
www.facebook.com/kb0177
Redog is offline   Reply With Quote
Old 11-21-2008, 07:26 AM   #12
Beholder88
GL Member
 
Beholder88's Avatar
 
Join Date: Jul 2008
Location: Butler, PA
Posts: 633
Beholder88 is on a distinguished road
Would this work with the stock wheels? Does the clearance change between the caliper and the inside of the rim? I've got both a set of the stock Alero Aluminum rims as well as a set of steelies for the winter. If I upgrade the brakes as shown, will they work with the wheels I have?
__________________
*TOTALED* - 2000 Olds Alero Sedan - 3.4L 3400 V6 - WAI - Sony Head Unit -
NEW RIDE - 2005 Buick LaCrosse - 3.8L 3800 Series III V6 - WAI - Muffler/Resonator removed -
Beholder88 is offline   Reply With Quote
Old 11-21-2008, 09:15 AM   #13
surreal_awakening
GL Member
 
surreal_awakening's Avatar
 
Join Date: Feb 2008
Location: Crofton, MD
Posts: 839
surreal_awakening is on a distinguished road
Send a message via Yahoo to surreal_awakening
Has anything ever developed on upgrades for the rears?
surreal_awakening is offline   Reply With Quote
Old 11-21-2008, 09:32 AM   #14
hok666
GLS member
 
Join Date: Dec 2003
Location: Midland, MI
Posts: 1,458
hok666 is an unknown quantity at this point
is there anyway to get rid of the corvette name on the calipers? Just think it would be dumb see corvette name on alero.
hok666 is offline   Reply With Quote
Old 11-21-2008, 09:36 AM   #15
surreal_awakening
GL Member
 
surreal_awakening's Avatar
 
Join Date: Feb 2008
Location: Crofton, MD
Posts: 839
surreal_awakening is on a distinguished road
Send a message via Yahoo to surreal_awakening
Can't you get the calipers from a parts store w/out the Corvette name on it?
surreal_awakening is offline   Reply With Quote
Old 11-21-2008, 10:59 AM   #16
alerored04
GLS member
 
alerored04's Avatar
 
Join Date: Jun 2004
Location: New Prague, MN
Posts: 2,481
alerored04 is an unknown quantity at this point
You can get them without the name. Redog, they actually fit with the stock 16" GLS wheels. If you have 15" wheels you will need to upgrade. The offset does not appear to have changed.
__________________
My car breaks alot.
(Notice I need someone to make me a sig?)
http://www.cardomain.com/ride/2598719/1
alerored04 is offline   Reply With Quote
Old 11-21-2008, 12:40 PM   #17
Cliff8928
Moderator
 
Cliff8928's Avatar
 
Join Date: Nov 2004
Location: Long Grove, IL
Posts: 5,002
Cliff8928 is on a distinguished road
Send a message via ICQ to Cliff8928 Send a message via AIM to Cliff8928
Quote:
Originally Posted by hok666 View Post
is there anyway to get rid of the corvette name on the calipers? Just think it would be dumb see corvette name on alero.

You can use GTO calipers. The name on those is just a decal.

The F-Body calipers also work, even if they aren't as well constructed they will be good enough for daily use.

Oh, and I agree. No logo on the calipers on the Olds. The Chevy is another story (have a freshly powdercoated set of C6 calipers for it)
__________________
Cliff Scott
2004 Alero GX w/sport pkg - Sold, living somewhere in WI now.
2011 Saab 9-5 Turbo4 M6
2004 Corvette Convertible M6
1994 Chevy Beretta - Quad4/M5
Cliff8928 is offline   Reply With Quote
Old 12-01-2008, 12:35 AM   #18
will176
GX Member
 
will176's Avatar
 
Join Date: Jun 2008
Location: Il
Posts: 61
will176 is on a distinguished road
sorry to be a noob, but if i have the standered 16 inch 6 spoke wheels, will these fit? or will i need to upgrade?
these ones-
__________________

2001 gls 3400 sfi

Last edited by will176 : 12-01-2008 at 12:38 AM.
will176 is offline   Reply With Quote
Old 12-01-2008, 12:51 AM   #19
alerored04
GLS member
 
alerored04's Avatar
 
Join Date: Jun 2004
Location: New Prague, MN
Posts: 2,481
alerored04 is an unknown quantity at this point
I am not sure if those work. Those are the '99 16" wheels. The ones I am using are the 01 GLS 16"s. If they are the same offset as mine then they should.
__________________
My car breaks alot.
(Notice I need someone to make me a sig?)
http://www.cardomain.com/ride/2598719/1
alerored04 is offline   Reply With Quote
Old 12-01-2008, 12:53 AM   #20
will176
GX Member
 
will176's Avatar
 
Join Date: Jun 2008
Location: Il
Posts: 61
will176 is on a distinguished road
whats your offset?
__________________

2001 gls 3400 sfi
will176 is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -4. The time now is 08:27 AM.


Powered by vBulletin Version 3.6.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.