11-29-2008, 07:07 PM
|
#1
|
|
GX Member
Join Date: Sep 2008
Location: Eastern, NC
Posts: 177
|
Oil Pan Removal
Has anyone removed the 3400 oil pan without removing the subframe, or the engine from the car? I have an oil leak from the pan gasket, but don't want to brake it loose to find out I have to take the subframe out.
__________________
One Bolt at a Time.
|
|
|
|
11-29-2008, 09:45 PM
|
#2
|
|
GL Member
Join Date: Dec 2005
Posts: 720
|
Hopefully, someone will chime in and say this stuff isn't necessary, but according to Haynes, you have to remove the:
serpentine drivebelt
belt tensioner
lower splash pan
oil-level sensor
A/C compressor
right side ball joint and lower control arm
front exhaust pipe
steering gear pinch bolt
flywheel/driveplate lower cover
starter
hood????
passenger side upper engine mount, then the lower
through bolt holding the driver's side transaxle mount to the frame
retaining bolts securing the mount to the transaxle
crankshaft pulley
Finally, the oil pan is ready for removal after unplugging some connectors and removing it's 12 or so bolts. Like I said, maybe someone can simplify this.
__________________
You don't mean much.
My mother is constipated!
Hurting you is not an issue
Your father is mistaken
|
|
|
|
|
11-29-2008, 10:36 PM
|
#3
|
|
GLS member
Join Date: Aug 2006
Location: Grand Forks, ND for school; Langdon, ND home
Posts: 2,632
|
you shouldn't have to take off that much just for the oil pan. but idk for sure wat u do.
__________________
2001½ F150 XLT Crew Cab- true dual glasspacks with x-pipe, AEM intake, SCT X3 with VMP custom tunes, full stereo system, HID 55w heads and 35w fogs, 35% tint front and 20% rear, Lightning tail lights
04 F6 Sno Pro Team edition- MBRP race can, ODS clutch kit
01 YZ125- bored out to 144, PnP cylinder and head, Pro Circuit WORKS suspension, many other mods
|
|
|
|
|
11-29-2008, 10:54 PM
|
#4
|
|
GX Member
Join Date: Sep 2008
Location: Eastern, NC
Posts: 177
|
Quote:
Originally Posted by CiscoPath
Hopefully, someone will chime in and say this stuff isn't necessary, but according to Haynes, you have to remove the:
serpentine drivebelt.....and so on.
,Finally, the oil pan is ready for removal after unplugging some connectors and removing it's 12 or so bolts. Like I said, maybe someone can simplify this.
|
This from experience or just the haynes service manual? Cause if its that bad im going to start buying bulk oil till the motor blows or the James Bond oil slick stops working.
__________________
One Bolt at a Time.
Last edited by Blktrax : 11-29-2008 at 11:00 PM.
|
|
|
|
|
11-29-2008, 11:00 PM
|
#5
|
|
GL Member
Join Date: Dec 2005
Posts: 720
|
^^nope, strictly from Haynes. In fact, I don't recall ever reading anywhere on here that anyone ever had a reason to.
__________________
You don't mean much.
My mother is constipated!
Hurting you is not an issue
Your father is mistaken
|
|
|
|
|
11-29-2008, 11:03 PM
|
#6
|
|
GX Member
Join Date: Sep 2008
Location: Eastern, NC
Posts: 177
|
Well thats another fear that it isn't the oil pan but the main crank seal on the trans side, witch of course the trans has to come out. But can't see. I put the engine oil UV dye in, and its press obvious on the back of the block mid pan there is an excess, but not dripping from above.
__________________
One Bolt at a Time.
|
|
|
|
|
11-30-2008, 02:12 AM
|
#7
|
|
Moderator
Join Date: Nov 2004
Location: Long Grove, IL
Posts: 5,002
|
Don't forget about a possible leak from the oil pump drive gear o-ring.
__________________
Cliff Scott
2004 Alero GX w/sport pkg - Sold, living somewhere in WI now.
2011 Saab 9-5 Turbo4 M6
2004 Corvette Convertible M6
1994 Chevy Beretta - Quad4/M5
|
|
|
|
|
12-02-2008, 03:40 PM
|
#8
|
|
GX Member
Join Date: Sep 2008
Location: Eastern, NC
Posts: 177
|
Quote:
Originally Posted by Cliff8928
Don't forget about a possible leak from the oil pump drive gear o-ring.
|
Yea thanks I forgot about that thing, the oops we dont need a distributor anymore but we'll leaving the leaky hole there anyway.
Put another one on the "what were they thinking" pile.
__________________
One Bolt at a Time.
|
|
|
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
|
|
|
| Thread Tools |
Search this Thread |
|
|
|
| Display Modes |
 Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -4. The time now is 05:45 AM.
|
