NEED HELP WITH HIDs

[billytheman1188]

Alright well i just got my 8000k lights from oznium, they didnt come with instructions, now i know its simple, but there is one thing.

i dont know what these wires go to.....

hold on i gotta go take a picture. be back soon to post the pic up

[billytheman1188]

http://aycu09.webshots.com/image/8728/2005311819357658212_rs.jpg (http://allyoucanupload.webshots.com/v/2005311819357658212)

http://aycu29.webshots.com/image/9548/2005389214216313913_rs.jpg (http://allyoucanupload.webshots.com/v/2005389214216313913)

[doubleN0alero]

they plug into your factory harness..

[billytheman1188]

oh and i have a stupid question(what else is new;))

How the fuck do i get that plastic peice that i screw the top onto off of the wires there, i screwed the top off, but i cant get that bottom peice off!

[brim]

haven't touch any HID stuff yet, but just ask on oznium or ask phil who runs the site, he'll help you out i'm sure

[billytheman1188]

they plug into your factory harness..

oh ok, thanks.

On a good note, my car is in the shop now cause i had that coolant leak, turns out he said he tightened the left bolt on the LIM about 3 quarters of a turn and he took it out for a long drive and it drove fine, no leak it was bone dry!:rolleyes2: so atleast i dont have to drop a shit load of money!:yahoo:

[billytheman1188]

haven't touch any HID stuff yet, but just ask on oznium or ask phil who runs the site, he'll help you out i'm sure

i called him, left him a message cause i didnt get the instructions, but im sure i will be fine, i was just confused about those wires.

oh and why did they give me 12 screws??? i know i have to drill holes if i cant use zip ties, but why would they give me 3 sets of 4 screws?? theres only 2 holes on each ballast.

[billytheman1188]

they plug into your factory harness..

hmm so someone told me "goodluck finding the factory harness", is it hard to locate???

[doubleN0alero]

its where your regular light bulbs plugged into....

[billytheman1188]

its where your regular light bulbs plugged into....

idk, i thought there was a peice that snaps into where the bulbs used to go?? those two little metal peices wont stay in where the bulbs plugged into....

lmao

[doubleN0alero]

okay...billy, do yourself a favor...pick up the phone book and start calling up shops and find out somebody that will just do it for you.

[billytheman1188]

okay...billy, do yourself a favor...pick up the phone book and start calling up shops and find out somebody that will just do it for you.

lol, i know this install is easy, when i pick up my car today and i get home i will look at it, im sure i will be fine, i just need to see what your talking about.

[cavaliers60]

I"m getting HIDs when I get those projector headlights done............... Whenever that happens... lol

[clutch1]

Who need projectors, you're not gonna be lookin into them ;)

[billytheman1188]

The HIDs look sweet!:rolleyes2:didnt take long at all, i will post pics later or tomorrow.

[cavaliers60]

Who need projectors, you're not gonna be lookin into them ;)

haha no, but I like the projector headlights that Anderbra?????? makes??? I think that's the guy who makes them... correct me if I'm wrong... but I like the way they look... If I don't get the projector lights, then I'm just gonna buy my silverstars.. lol

[teflone]

I put my HIDs in a few days ago...

I found that it was easier to pull the factory harness, back to the (daytime running lights) hole, this was not easy.. as I had to cut the factory harness,and pull it through the other hole, closer to where the light assembly connector plugs into..
and since my HIDs were backwards, I soldered the factory harness backwards.. as in orange to white wire, and white to orange wire to give the ballasts the right polarity..

I found there is no room behind the night headlamps.. and running all those extra harnesses was next to impossible to do right, and not have all the harnesses resting on the top of the headlamps.. (not an ideal spot, specially driving in the rain)

So now all power wires for the ballasts come out of the daytime rubber cup hole, and the HID feed wires are the only ones going into the night headlamp rubber cup..

Nice and neat, and away from the rain..