HID's

[strtrydr]

Okay ... did a search and found some information but I wanted to know from the people that have bought HID Conversions; Where did you buy them from?

Thanks In Advance.

[Silentalero]

oznium.com and projectors = :)

[strtrydr]

^soon to be me too ... as soon as I figure how to make 90mm Hella Projectors fit in the headlamp :)

[antichrysler]

Good luck with that. If you can get em in there it'll work pretty slick. The headlamps for the alero aren't exactly the best design.

[Silentalero]

im still not sure what size mine are but from the reaction at ass, everybody loved em.

[teflone]

Ebay, MC Motoring, out of toronto
Affordable too, only got reflectors, Projectors would be nice..

[Redog]

im still not sure what size mine are but from the reaction at ass, everybody loved em.

They were pretty cool

[alerocar01]

mark post up a picture of your projectors. I want to see what they look like. thanks.

[clutch1]

Surf around the ASS section and you'll eventually find a pic of them if Mark doesn't post one up here ;P

[MixtapeMessiah]

I got Hella 6500k hids, fits fine in my headlight housing, cost me a good 400 bucks tho
http://i116.photobucket.com/albums/o27/aleroonchrome00/Picture410.jpg

[clutch1]

Oznium.com sells kits for $230 for 2 bulbs n 2 ballasts and has umatched customer service.. just incase anyone was lookin for some.

[Gr1m]

i paid like 260 for my 10000k's at a local sound/security store. one of my fav mods done so far

[MixtapeMessiah]

my favorite also, everyone always tells me to put my lights on so the ufos can see and come land, its pretty fuckin funny.

[lilfee504]

not good pics but i got mine for 88 bucks off ebay...hey they may be cheap but oh well i like em! 8000k BTW they look great at nite tho

[MixtapeMessiah]

88 bucks? damn thats cheap compared to mine lol

[Satsuriku]

based on what ive seen with HID's, you get what you paid for :(

[MixtapeMessiah]

^^^exactly, theyll prolly crap out soon, as for mine theyll last a longggg time for 400 bucks a set, hella go hard

[strtrydr]

im still not sure what size mine are but from the reaction at ass, everybody loved em.

if you dont mind can you e-mail me some pictures of how yours is setup so I have an idea on what kind of work I am going to have to do for the projectors

[Silentalero]

i wish i could but i dont think anybody even got pics of the headlights. And right now my headlights are torn back apart because i need to figure a way to put the cutoff in there (ask randy, im blinding people) plus i gotta seam the edges.

[clutch1]

There's a couple pics with the projectors in them when they took pics of the OSV damage or flat tire or something, I know I saw them when I surfed through all of them.

[steve-o]

Ebay, MC Motoring, out of toronto
Affordable too, only got reflectors, Projectors would be nice..

ditto
8000k pics
http://img.photobucket.com/albums/v212/steveoz24/HID2.jpg
http://img.photobucket.com/albums/v212/steveoz24/hid1.jpg

[strtrydr]

^nice ...

Okay one last question ... any one got pictures of how they are wired and where the ballasts are hidden/mounted. thanks again.

[steve-o]

I mounted mine right between the lights. so far no problems, I might relocate later though.

[teflone]

I mounted my ballasts between the washer fluid resv, on one side..
and the coolant overflow resv. on the other..

I wouldnt worry about mounting them, there is ALOT of room in my v6 alero to mount them anywhere..

Just make sure they are secure and not going to rattle around much, the only water protection I would suggest is that the stock, and HID ballasts connectors are out of direct water, rain and what not..

I went the extra mile and wrapped them in electrical tape..

the connectors (kaba) on the HID's are all waterproof. never saw any of them that are'nt

But the stock power connector in your headlight chasis isnt waterproof.

I ended up pulling the stock light harness out of the DaytmeR lights hole to give me more length of wire to work with..

I also also ran into alot of HID's that are backwards in polarity.. mine were as well..

I cut the stock harness off and re-soldered it backwards so that the polarity for the HID's was correct..

This is all stuff I thought that would work and look good. go with whatever works.. ;)
Good luck

[teflone]

I mounted mine right between the lights. so far no problems, I might relocate later though.


Where ????? I dont follow..