Question...

[Christato71]

This might be a dumb question to ask but I'm having some trouble with it. I cant really figure out how to replace the light bulb located where the red arrow is...:lol:

http://i32.photobucket.com/albums/d25/nickdahommie/00.jpg

[cherrington17]

in the cubby hole? you have to remove the shifter, shift bezel (plastic under shifter), radio bezel (plastic around radio) and its in there.

its easy to get to.

the shifter has a staple in the front bottom of the handle, the staple pulls out, shifter pulls up, shift bezel pulls up, radio bezel pulls out toward the seats. make sure you disconnect the harnesses too.

[Christato71]

That's what I thought, but is there any other way of doing it? I'm afraid of braking something if I start taking everything apart

[cherrington17]

it would be REALLY hard to break anything. it just all pops into place and pulls out rather easily.

and no... there is no other way.

[whiterider00]

it would be REALLY hard to break anything. it just all pops into place and pulls out rather easily.

and no... there is no other way.

it wouldnt be that hard to break something. i did. the radio bezel has clips all around it, and if you just yank, it could crack, especially where its thinner up at the top part. just take your time and go slowly. should pop out pretty easily.

[paradigm9]

i was able to get down on the floor from the drivres side and reach my arm in there and pull the bulb and socket out to replace, its kinda tricky because the socket has tabs on it that need to be pulled out to get it out of the hole it sits in but was not that bad

[Gr1m]

it would be REALLY hard to break anything. it just all pops into place and pulls out rather easily.

and no... there is no other way.

i wouldnt says its hard to break it, lol ive snapped a radio bezel trying to get it out

[Christato71]

i was able to get down on the floor from the drivres side and reach my arm in there and pull the bulb and socket out to replace, its kinda tricky because the socket has tabs on it that need to be pulled out to get it out of the hole it sits in but was not that bad


How did you manage to get the socket out? I only could get the clips off

[Christato71]

Alright after many attemps I managed to get the bulb harness out but I'm having some trouble getting the bulb out, any ideas?

[cherrington17]

don't use pliers. the bulb tends to explode into a shower of broken glass.

[Christato71]

I'm not sure how to get it out because it's so small

[alerogls001]

i had the same problem with some small bulbs. everything was too slippery to get a grip too- what worked for me was the stuff you put on the surface of like kitchen cabinets and drawers. worked like a charm.

[Christato71]

what was this stuff called? I am going to attempt to take out the bulb again tomorrow sometime

[alero_bmxer]

its like a kitchen drawer liner.

[Christato71]

Well upon further investigation, I believe this light is hardwired into its wiring or the harness

[robalero]

use a patatoe to get the bulb out ( patatoe cut in half of course )

[Christato71]

This is what the bulb looks like:
http://i32.photobucket.com/albums/d25/nickdahommie/Mobile%20Uploads/0711001346.jpg

[robalero]

take it off the clipping and its a twist bulb from the looks of it

[Christato71]

the gray clip you see there doesn't do anything from what I've seen, it just like un-clips. And the bulb doesn't twist out at all, I've tried that too :(

[robalero]

hop on over to a GM dealer parts specialist and ask them I sure they might be able to help you

[$hawn]

Pull the bulb straight out, might have to wiggle it around a bit to loosen it though.