3500 swap in the works....

[billytheman1188]

The time has come....3500 will get swapped in....port and polished upper and lower intake mani with 65mm TB and the S&S headers i have on the 3400..gonna swap them right over :) Going through WOT-tech

[Redog]

Good luck with the swap. Keep us posted

[kwhauck]

Full 3500 swap, or just top end?

[xXManwhoreXx]

Good luck man...

[99-alero]

needs moar 5speed

[MMGT1]

When you're done, meet me at the track.... lets see how you fair against a 3400, wink, wink...

[billytheman1188]

Full 3500 swap, or just top end?

Full swap

When you're done, meet me at the track.... lets see how you fair against a 3400, wink, wink...

LOL....you prob have yours all built up right? judging by the posts you make im assuming you do....if not, LETS GO! ;)

[MMGT1]

Yea its built. I was thinking you were building a 3500 and dropping it in. I am dying to see how I would do against a built 3500

[billytheman1188]

Yea its built. I was thinking you were building a 3500 and dropping it in. I am dying to see how I would do against a built 3500

Not really gonna build up the engine too much. just getting the upper and lower intake mani's port&polished, bigger tb, headers, exhaust. 200+ hp is enough for me. Canada is a little far a drive too...lol

[guiguilandry]

good luck I wanna see this !!

[billytheman1188]

K....im searching for possible sites to buy an engine from but i dont wanna just buy from ANY site....found this one.


http://www.psengines.com

then i did a little search and found a 3800 supercharged on there....no 3500 but im sure i could request one. There is a 97-05 buick built 3800 supercharged....its very tempting....but first i should talk to guild about how much goes into that swap.....both swaps i would need to do A LOT of work right? like swapping computers and stuff....$2,179 for the 3800:cry:

[jawa]

for the 3500 its pretty much a bolt in engine, all you need is the 65 mm TB and the adaptor, you also need the crank position sensor relocation kit avaiable from WOT

[billytheman1188]

for the 3500 its pretty much a bolt in engine, all you need is the 65 mm TB and the adaptor, you also need the crank position sensor relocation kit avaiable from WOT

Nice....did you do the swap?

[Shiwnath]

The 3500 uses a different MAP sensor...i think you'll need a pig tail to get it work.... PM 3500Alero he actually had this swap

[G.I.Ceo]

You can get all the stuff you need for the swap at MilzyMotorSports.com.

[jawa]

Nice....did you do the swap?

not yet im not finished gathering all the parts i need, when i do mine its getting a 5 speed as well, you kno so all that power wont get soaked up by the auto tranny lol

[99-alero]

my buddy has a ga 3.5 swapped with 5speed, motor was a direct swap tranny was a pain tho

[jawa]

yea not looking forward to the tranny thing

[zearchyo]

Okay ,sorry for being a total moron when it comes to the aleros v6 power plants since i my self got a 2.4l twin cam, don’t really know much more like nothing about those two engines. What exactly would be the benefit of doing this engine swap. Pleas enlighten me with the knowledge I seem to lack.

[G.I.Ceo]

Okay ,sorry for being a total moron when it comes to the aleros v6 power plants since i my self got a 2.4l twin cam, don’t really know much more like nothing about those two engines. What exactly would be the benefit of doing this engine swap. Pleas enlighten me with the knowledge I seem to lack.

Better compression, better flow, better crank, and more HP. The G6 motor is essentially the same motor but it was a little redesigned internally with the crank, cylinder heads, and intakes. Plus stock it is a 200HP motor. The cool thing is everything bolts up the same minus a few sensors that have to be changed over.

[zearchyo]

cool, thanks!

[billytheman1188]

this bad boy will fit right?

http://www.ebay.com/itm/ENGINE-07-2007-CHEVY-MALIBU-IMPALA-G6-3-5L-V6-LZ4-MOTOR-VIN-N-LZ4-/170708959121?fits=Model:G6&hash=item27bf0bff91&item=170708959121&pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr#ht_2167wt_1112

or this one.....

http://www.ebay.com/itm/USED-ENGINE-WARRANTY-G6-2007-3-5L-35K-MILES-/140450929716?fits=Model:G6&hash=item20b3871c34&item=140450929716&pt=Motors_Car_Truck_Parts_Accessories&vxp=mtr#ht_2583wt_1109

[JLw7123]

i say the second one.

[kwhauck]

Neither one will work, those are the wrong version of the 3500....

this is what you want....

http://www.ebay.com/itm/ENGINE-2005-05PONTIAC-G6-LX9-3-5L-V6-MOTOR-VIN-8-8th-digit-/120791668860?pt=Motors_Car_Truck_Parts_Accessories &fits=Model%3AG6&vxp=mtr&hash=item1c1fbe987c

[billytheman1188]

81,000 miles.....that sucks....lol.....what would i need for a little rebuild? i want this to be reliable and i would prefer low miles....i will do some searching, thanks a lot man.

[billytheman1188]

http://www.ebay.com/itm/05-PONTIAC-G6-ENGINE-MOTOR-3-5L-VIN-8-8TH-DIGIT-46K-/360209065293?_trksid=p4340.m185&_trkparms=algo%3DSIC.NPJS%26its%3DI%26itu%3DUA%26o tn%3D5%26pmod%3D170607485592%26ps%3D63%26clkid%3D4 018959402374065697#ht_2435wt_1112

[Shiwnath]

http://www.ebay.com/itm/2006-CHEVY-MALIBU-PONTIAC-G6-LX9-3-5L-V6-ENGINE-LX9-06-/400255202593?pt=Motors_Car_Truck_Parts_Accessories &vxp=mtr&hash=item5d3111b521

Description:

ENGINE HAS ONLY 32,000 MILES!!!

This is a good used 3.5L 4 cylinder engine(see full fitment/interchange below). This is a good engine that was tested and ran great in the vehicle. This is a longblock, with exhaust and intake manifolds and harmonic balancer. This is just a replacement motor, computer or catalytic converters are not included in this auction.

Interchange (for exact factory fit):

Hollender interchange shows to fit (5435):

06 G6 (3.5L (VIN 8, 8th digit))

06 Malibu (3.5L (VIN 8, 8th digit))

Shipping

We have trucks that leave every day at 3pm, so you get your parts fast. .

Please message me through eBay, including your zip code, for a freight quote. Typically freight costs are higher for residential locations, so be sure to specify if you are a shop. If you want to arrange a pickup yourself we will only charge a $30 palleting fee and TN sales tax.

Doesn't get better than that :D

[jawa]

Fail

[billytheman1188]

hahahahaha, wow....

[kwhauck]

www.car-part.com (http://www.car-part.com)

http://www.car-part.com/cgi-bin/search.cgi?userSearch=int&userPID=1000&userLocation=All+States&userIMS=&userInterchange=B%3D%40BO&userSide=&userDate=2005&userDate2=2005&dbModel=61.27.1.1&userModel=Pontiac%20G6&dbPart=300.1&userPart=Engine&sessionID=600000000000000000010832098&userPreference=zip&userZip=12220&userLat=42.6656&userLong=-73.8815&userIntSelect=473690&userUID=0&userBroker=&userPage=1&iKey=

There is a motor with 74k, about 100 miles from you, for $299...........

[billytheman1188]

www.car-part.com (http://www.car-part.com)

http://www.car-part.com/cgi-bin/search.cgi?userSearch=int&userPID=1000&userLocation=All+States&userIMS=&userInterchange=B%3D%40BO&userSide=&userDate=2005&userDate2=2005&dbModel=61.27.1.1&userModel=Pontiac%20G6&dbPart=300.1&userPart=Engine&sessionID=600000000000000000010832098&userPreference=zip&userZip=12220&userLat=42.6656&userLong=-73.8815&userIntSelect=473690&userUID=0&userBroker=&userPage=1&iKey=

There is a motor with 74k, about 100 miles from you, for $299...........

There is one in kinderhook with 25k on it....kinderhook is like 30 miles from me....hmmmmmm

[billytheman1188]

Ok so now its time to find an engine....found one close by with 25k. Now i just need confirmation on the stuff needed for the swap.....crank position sensor and isnt a lower engine mount needed? I cant find JUST a swap kit on milzys site....and mike/ben haven't replied to my email yet. I need to know exactly what needs to be changed so i can tell my buddy.... PLEASE HELP! :)

I will do some more searching for some answers but i haven't had any luck.

[billytheman1188]

K. Just talked to mike about the kit....def ordering that soon. He told me that i shouldn't switch over to the fel pro gaskets cause GM used a diff gasket on the 3500s and their actually better. So looks like this is gonna be an easy weekend job. Also ordering a new tranny mount cuase the stock one is DONE. lol. Can't wait to get this done. If the parts that i need dont take too long to get to me then this should be done not this upcoming weekend but the next. PUMPED!

[billytheman1188]

Just a link for anybody who may wanna do this in the future.....

http://dl.dropbox.com/u/534555/3500%20N-Body%20Swap.docx

[Hellfire5670]

I'm excited for you :P cant wait to see it in the car!

[xXManwhoreXx]

Any updates?